No backlight LED Screens Part 2

No backlight LED Screens Part 2

Usually when you want to find what is the problem with this faulty type you will have to use a lot knowledge.
There are many possibilities when you don’t have any backlight, let’s list them.
Cable , screen, motherboard near connector or fuses, video card or my favorite water spillage with rust.

1.Checking the cable can be done in 3 ways or verify.
The first and the simple way is to change the cable and see if you backlight its back.
Checking the cable can be done manually with a multimeter.I personaly i do that ,if its the last resort, if i don’t have another alternative.

2.When the screen its bad usually you can change it, but this is the faulty with the smallest probability to happen.
If the scre actually is bad the there are 2 possibility : the fuse is bad or the if that handle everything for then screen its bad or burn. I saw cases! Its not worth to fix.

3.OK! Motherboard not providing power for the screen. Just a second I’m checking for space because here I can write all day 🙂 .
I’ll start with some basic reading from a laptop schematic.
3vlcd, 3v, BL_ON, vadj,lcdvdd,etc
Usually when you check for those voltage on the connector you will need to find max 3 types of voltage : 3.3, 3 and 12v.
When you don’t find them you can take them from another side.
There are few notebooks that don’t have a fuse and you need to find what wrong.
If the voltage is there that means its the cable but be sure to test it with another screen.
My last repair was on a HP CQ71 and the notebook was missing the adjust voltage, you brightness on the screen, with vadj1 signification on the schematic.
There was 2 option to find the 3.3 v adjustable .
3.3v means 100% brightness and I think 3 or 3.1 v minim on brightness.
The second and my favorite its to connected direct to a stable 3.3v with a jumper(wire).

4. When it comes to video repair in a notebook that’s bad.
There are many videos online how reflow .
I saw many notebooks that had problems with backlight because of the GPU.
For me the number one with no backlight its dell , that GPU tend to fail a lot.

5. Corrosion in a notebook its biggest enemy with dust.
Last notebook with that problem was a HP 6930p elitebook.
I don’t know what happen but I saw the motherboard had met the water super serious.
In this case a coil that provided the main voltage for the screen was missing, with B+ signification. The problem was not that simple Because the coil was fried and it was not the only component bad. Near the connector there where 2 capacitors that was shorted.
Because I was in a rush I just remove them and supply the voltage from the coil pad to B+ so the screen will have backlight.
When you bypass the voltage you will not be able to use the brightness function, it just depends on what problem you encounter.

If have any questions please tell me because I will be glad to help with any problems related to this type of faulty.
Be safe and good luck.

No Backlight part 1 ccfl

No Backlight part 1 ccfl

I just want to say hello to all and thank you for reading my post.

Usually when I need to repair a notebook that has this problem I go straight to the screen and I change it or I test It with a smash screen only to see if the lamps powers up.
The difference between ccfl screens and led is that ccfl has a actual neon inside the screen and the led screen got foil with led fitted on it.
To power up that neon inside the screen it needs a lot of voltage so invertor convert that 12v to the amount of voltage it requireds.

Repairing a no backlight problem to a notebook relates to 3 major comcomponent:
Cable, invertor and screen(neons)
1.Checking or verifying a cable its a slow but not hard work, you only need to patient.
Set the multimeter on continuity and use a wire to insert in the connector.
2.Checking the invertor its a little complicated because you can repair it if you got some basic knowledge of electronics.
The basic and the only think you can do is to check the fuse and for cold joints on the transformer.if you really want to repair it you need to check the smd capacitors, transistors or DC DC convertors but when you start to dig ,you will reach a point when you will say its not worth it. It actually not worth fixing a inverter because they are so cheap to buy. My opinion!
3. Checking a screen its very easy, like if you wanna know if the lamps are bad.
You just need to disconnect the lamps cable and connect other( similar) lamps or connect a smash screen, only the lamp cable.
When you power up the notebook you will see that the lamp will start on the smash screen and image will be on your notebook.
BEWARE of short circuit when applying this metod.

That’s it . If you want to change the lamps from the screen you need to watch a video online how to take it apart.

Be safe and good luck with the diagnostic.

How to FIX HP Cooling fan error 902

HP fan error 902

Every Hp that shows the fan error will block the notebook from booting because its hardware problem.
If you don’t know how to take it apart search for a video on YouTube and find the model that you have.
Use it as a guide to take it apart because you need to reach the fan system.
If your uncomfortable to take it apart , go to a computer shop and tell them what to do for your.

Let’s start! How to fix this Error 902
A friend ask me to take a look at the notebook , he said that he can’t boot because of that error. When I saw it I said that we might need to replace it.
So I took the notebook apart and before I went to order the fan ,I ask my friend Can I take that fan apart and see what happen ,why did it fail.

When I started taking it apart I saw a wire moving.
DSCN4499
DSCN4501
AaAhh the irony. I told him wait a few minutes with the order and let me see if resolder the wire what happens.

After I resolder and installed back the system cooling the notebook started normally without that error.
This error is related to ALL the HP notebooks, even if you can’t repair the fan you can replace it and the error will go away.
If you can’t, you can replace only the coil but it needs to be with 3 wires: red,yellow,black.
When you replace the coil you need to put the original ventilator so it can fix in the axe.

I did test the notebook with another fan to see if the error goes away.
Yes it did go away, but I needed a proper fan so i can fit in the notebook spot.

If you encounter any problems please post a comment or PM , I will be glad to help.

Take care and good luck with your problem.